?

Triflex HeatTec technical details

Triflex HeatTec - technical details

Triflex HeatTec: surface heating system for entrance and exit areas in car parks


The Triflex HeatTec system was developed as a surface heating system for car park entrance and exit areas. It can withstand the high mechanical and chemical loads required in these areas. The Triflex HeatTec heating system can also be used for other pedestrian and vehicular outdoor areas. These include platforms, helicopter landing pads, walkways, balconies, staircases and much more.


Advantages over electrical thin-bed heaters:
 

  • Low layer configuration within 10 mm so ideal for refurbishments without total demolition, no sill construction or height differences.
  • With all the advantages of a waterproofing system which is suitable for vehicular traffic, a joint-free robust construction with simultaneous aesthetic requirements can be produced.
  • High efficiency due to minimal covering of the heating at approx. 5 mm
  • Fast heating even in low temperature areas
  • Proven cost reduction of up to 30% through energy savings
  • Further cost savings by shortened construction time due to combining the heating and waterproofing or protection work.
  • No impact on functional efficiency in the event of minor damage to the heating element
  • Quick and easy installation by trained personnel
  • Uniformly tested and approved system with proof of functionality and assurance of durability by an independent institute

Triflex HeatTec system set-up

Thumbnail
1

Primer

Triflex Cryl Primer 222

Triflex Cryl Primer 222

Triflex Cryl Primer 222 is used as a primer on asphalt for Triflex systems with a PMMA resin base.

Consumption
Min. 0.40 kg/m² on a smooth, even surface

Triflex Cryl Primer 287

Triflex Cryl Primer 287

Triflex Cryl Primer 287 is used as a primer on absorbent substrates such as concrete, screed or wood for Triflex systems with a PMMA resin base.

Consumption
Min. 0.35 kg/m² on a smooth, even surface

Triflex Pox Primer 116+

Triflex Pox Primer 116+

Triflex Pox Primer 116+ is used as a primer, a filling primer and a roughness depth levelling material, primarily in the Triflex CPS-C+ and Triflex CPS-I+ systems.

Consumption
The volume depends on the system being used
2

Adhesive

Triflex HeatTec Adhesive EP

Triflex HeatTec Kleber EP

Triflex HeatTec Adhesive EP is a fast-curing, ready-to-use, highly viscous filling compound for gluing in Triflex HeatTec heating laminates.

Consumption
Approx. 6.0 kg/m² with a roughness depth = 0.5 mm
3

Heating element

Triflex HeatTec heating laminate

Triflex HeatTec Heizlaminat

The heating laminate is used in the Triflex HeatTec outdoor heating system for ramps, entrances and exits, terraces and pergolas. It can withstand high mechanical and chemical loads in these areas.

Consumption
/
4

Waterproofing (Triflex ProPark or Triflex BTS-P)

Triflex Special Fleece

Triflex Spezialvlies

Triflex Special Fleece is used for reinforcement and layer thickness control with Triflex PMMA and PUR systems.

Consumption
/

Triflex ProTerra

Triflex ProTerra

Triflex ProTerra is a high-quality and durable surface waterproofing product for use on balconies, terraces and covered walks in both new buildings and refurbishments. Triflex ProTerra can be used with the Triflex BTS-P, Triflex BWS and Triflex Stone Design systems.

Consumption
Min. 3.00kg/m² on a smooth, even surface
Product information

Triflex ProPark

Triflex ProPark

Triflex ProPark is used in the systems Triflex ProPark und Triflex AWS. It is a high-quality and durable fleece-reinforced surface waterproofing product for use in both new buildings and refurbishments.

Consumption
Min. 3.00 kg/m² on a smooth, even surface
Product information
5

Wearing layer (Triflex ProPark or Triflex BTS-P)

Triflex Cryl Finish 205

Triflex Cryl Finish 205

Triflex Cryl Finish 205 is used as a finish on dressed and undressed Triflex PMMA systems to increase chemical and mechanical resistance.

Consumption
Approx. 0.50 to 0.70 kg/m² on a smooth, even surface depending on area of use.

Triflex ProFloor

Triflex ProFloor

Triflex ProFloor is used as a high-quality and durable coating for heavy-duty surfaces in the Triflex BTS-P, Triflex BFS and Triflex TSS balcony systems.

Consumption
Min. 4.00kg/m² on a smooth, even surface
Product information

Triflex DeckFloor

Triflex DeckFloor

Triflex DeckFloor is used as a high-quality, durable coating for heavy-duty surfaces in the parking deck systems Triflex ProPark and Triflex DeckFloor. Triflex DeckFloor can also be used to produce scratch and levelling coats in multi-storey car parks.

Consumption
Min. 4.00 kg/m² on a smooth, even surface
Product information

Triflex Cryl Finish 209

Triflex Cryl Finish 209

Triflex Cryl Finish 209 is used as a finish on enhanced parking deck systems to increase the chemical and mechanical resistance

Consumption
Approx. 0.50 to 0.70 kg/m² on a smooth, even surface depending on area of use.
6

Other/optional system components

Triflex Cryl RS 240

Triflex Cryl RS 240

Triflex Cryl RS 240 is a fast-curing, heavy-duty repair mortar for repairs to screeds and improvement work in exterior areas for thicknesses of 5 mm to 50 mm.

Consumption
Approx. 2.20 kg/m² per mm thickness on a smooth even surface.
Product information

Triflex Cryl Paste

Triflex Cryl Spachtel

Triflex Cryl Paste is used to level out any unevenness in the substrate and any fleece overlaps or depressions in Triflex systems.

Consumption
Approx. 1.40 kg/m² per mm thickness on a smooth even surface.

Triflex Cryl RS 242

Triflex Cryl RS 242

Triflex Cryl RS 242 is used for repairing and levelling work on asphalt coverings with layer thicknesses of 5 to 50 mm.

Consumption
Approx. 2.20kg/m² per mm thickness on a smooth even surface.
Product information

Triflex DeckFloor

Triflex DeckFloor

Triflex DeckFloor is used as a high-quality, durable coating for heavy-duty surfaces in the parking deck systems Triflex ProPark and Triflex DeckFloor. Triflex DeckFloor can also be used to produce scratch and levelling coats in multi-storey car parks.

Consumption
Min. 4.00 kg/m² on a smooth, even surface
Product information

Triflex Cleaner

Triflex Reiniger

Triflex Cleaner is used with all Triflex PMMA, EP, PU and PUA products. It is used to pre-treat substrates and to degrease metal when overcoating or if work is interrupted. In addition, soiled tools can be cleaned with Triflex Cleaner.

Consumption
Depending on the degree of soiling and the substrate (at least 0.20l/m²)
Product information

Instructions for use

Thumbnail
Laminates and cable shafts are marked according to the installation plan.
1/9
Thumbnail
Cut-outs and slots for junction boxes, sensors and cables are cut.
2/9
Thumbnail
Then two coats of Triflex Cryl Primer 287 are applied and sanded twice.
3/9
Thumbnail
Triflex HeatTec Adhesive EP is applied over the entire surface with a serrated trowel...
4/9
Thumbnail
...and glued to the Triflex HeatTec heating laminates removing all cavities.
5/9
Thumbnail
Then the ice and snow sensor as well as the temperature sensor are installed.
6/9
Thumbnail
Electrical connections are made according to the installation plan.
7/9
Thumbnail
Gaps between the heating laminates are evened out using Triflex DeckFloor mortar.
8/9
Thumbnail
This is followed by the further Triflex ProPark work steps without a further primer.
9/9

References

Thumbnail
Access ramps and delivery area of the administration building of the VHV Group Hanover
Thumbnail
Telekom Traunstein underground car park
Thumbnail
Spindlers Hof Berlin underground car park and ramps
Thumbnail
Town hall multi-storey car park Kaufbeuren
Thumbnail
Aalen Town Hall multi-storey car park ramp
Thumbnail
Weimarer Straße Wolfsburg multi-storey car park
Thumbnail
Kurt-Schumacher-Ring Salzgitter multi-storey car park
Thumbnail
“Kaufhaus des Westens” Berlin ramps in multi-storey car park 1
Thumbnail
Evangelical Hospital Bethel (EvKB) Kantensiek multi-storey car park

How may we help you?

We are here to help. Why not give us a call if you have any questions about our products and system solutions.